Search among more than user manuals and view them online Find great deals for Aton DLA4 Four Room Speaker Switch With Volume Control. Shop with confidence on eBay!. Free Shipping on many items across the worlds largest range of Aton Dla4 In Home Audio Equalizers. Find the perfect Christmas gift ideas with eBay.
|Published (Last):||23 November 2008|
|PDF File Size:||8.90 Mb|
|ePub File Size:||3.64 Mb|
|Price:||Free* [*Free Regsitration Required]|
ATON DLA4 Installation manual |
Set the Zone 2 volume level to the point where it achieves the maximum listenable level prior to distortion. Push a button – your speakers come on. Reconnect or test with known good IR Emitters. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Turn power for the output device OFF before making connections.
When using this setting, maximum volume is reduced to 10 steps. Make sure to match the impedance of the speakers and ampliers as noted. If within the applicable warranty period above purchaser discovers that such item was not as warranted above and promptly contacts ATON at or service atonhome.
The foregoing warranties do not cover reimbursement for labor, transportation, removal, installation or other expenses which may be incurred in connection with repair or replacement. Speakers in room miswired or defective a. Test known good speaker at back panel speaker connector b.
The IR indicator will be solid red when the room dlaa4 off, solid off when the room is on, or solid doa4 when the room is on and unselected. Adjust the volume as required. Press the Room Button for the desired room. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus including amplifiers that produce heat. Programming additional remotes can be accomplished in a matter of seconds. Lift up each ip-lock connector until it is locked in the up position.
ATON DLA4 Stereo Receiver User Manual
IR signal not reaching Room input. Source IR Emitters unplugged or defective. Setting the Maximum Turn-On Volume Level to the highest volume level will essentially disable Maximum Turn-On Volume the room will always come back on at the last volume level prior to turning the room Off.
Turn a knob, and the volume goes up or down. Please report the problem to your dealer immediately. Use the optional RF remote to turn the volume down in their room instantly from the den. Use Rack screws not included to attach the assembled unit to the equipment rack as shown in Figure D Functions this way to protect amplier.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. Remote Control Options Option 1: Severe personal injury and equipment damage can result by not following proper cla4. Most speakers are 4 or 8 Ohms.
Aton Dla4 In Home Audio Equalizers for sale | eBay
Do not apply excessive amplification. If it ickers, IR ooding is indicated. Room appears to be on and selected but unabled to be controlled using front panel buttons. Miswired speakers most likely cause. Remote Control batteries are dead.
This application provides independent control of each area within a sub-zone. Ground loop Ensure proper grounding using a three prong grounded AC outlet. The RF Receiver Base utilizes mounting holes to mount the unit to a wall, cabinet or other surface.
Aton DLA4 Four Room Speaker Switch With Volume Control
Without releasing the Room button, press and hold the Vol – Button. Once the Scene Preset has been saved, the Room LEDs for the rooms included in the Scene Preset will blink on and off four times and the system will return to the levels prior zton setting the Scene Preset.
See above Perform steps above 2. Set the volume in each room to the desired level. It is not necessary to point ayon remote at the main unit in order for it to function.
Atkn Presets override Default Volume Levels. Figure and Table provide descriptions and locations of Front Panel controls and indicators. Like the previous example, a pair of speakers are connected to the DLA2s Room 1 Speaker Outputs, while an additional pair of speakers is connected to the Room 2 Speaker Outputs.
Increase the separation between the equipment and receiver. Press Play, turn ON, etc. Cut the ends of the wire to length, allowing some free play about 6 inches of slack to allow for movement when physically connecting the wire.
This equipment generates, uses and can radiate radio frequency energy and, if not in-stalled and used in accordance with the instructions, may cause harmful interference to radio communications. Verify connections No audio present in any room Hum or buzz through system speakers Poor audio quality 26 1.
To set a Scene Preset: Warranty service requests made without proof of date of purchase will be denied.